Options – Peaktronic Positioner for Electric Actuated Gate Valve
The DHC-200 positioner is a high performance, high resolution digital positioner. A simple three button control is used to configure ALL parameters that the unit needs for a variety of applications, and eliminates the need for special meters and/or tools for calibration. As long as there is supply power, the unit can easily be field calibrated
This positioner can be calibrated for various command types (such as 4-20mA, 1-5VDC, 0-5VDC, 0-10VDC, or digital) and also the default operation upon loss of command (such as fail open, fail close, or fail as is). The optional transmitter/auxiliary switch module is installed into the positioner card via plug and socket. This allows a user defined feedback signal of current or voltage, and provides 3-SPSt relay contacts for open position, closed position, and a fault condition.
New DHC postioner - Gen II
Please note: The new Gen II DHC positioner can be easily identified with three LED’s located at the bottom of the positioner. The old style does not have any LED’s.
Click here to get a copy of the OM Manual for the new positioner
Resources
Specifications
Size:
S92, A92, B92, C92
Torque:
400 in/lbs – 2000 in/lbs
Voltage:
120vac, 1-phase, 50/60Hz
Switches:
Two (2) single pole, double throw (2SPDT) , 15 amp rated
Cycle Time per 90:
15 seconds for S92 & A92*,
32 seconds for B92 & C9*
Maximum Ambient Temperature:
150 F
Amp Draw:
S92 = 0.5A
A92 = 0.8A
B92 = 0.5A
C92 = 1.0A
Duty Cycle:
S92 = 100%
A92 = 75%
B92 = 100%
C92 = 50%
Conduit Entry:
Two (2) 1/2″ FNPT
Series 92 Standard Features
- Reversing, brushless capacitor run motor (115 VAC & 230 VAC)
- All 115 VAC and 230 VAC motors are CE Compliant, and bear the CE mark
- Integral thermal overload protection for motor windings with automatic reset (115 VAC & 230 VAC)
- 50% – 100% duty cycle motor
- Permanently lubricated, Rockwell hardened solid alloy steel gearing
- Combination Type 4X, 7, & 9 enclosure for use in various environments
- Corrosion Resistant thermally bonded baked powder coating with stainless steel trim
- ISO mounting configuration
- Two (2) 1/2″ FNPT conduit entry to eliminate cross feed between control, feedback, and power signals
- Highly visible beacon position indicator for positive position of valve, even at a distance
- Declutchable manual override: Pull up on indicator knob, insert 5/8″ wrench onto flats and rotate in the appropriate direction (CCW for open/CW for close). Models with handwheel override do not require a wrench. Simply push down on handwheel until engaged with cam and rotate
- Output torque: Series 92 actuators have an output torque range from 400 in/lbs to 2000 in/lbs
Positioner Standard Features
- High resolution
- Simple Pushbutton calibration
- Calibrated as standard or reverse acting
- Multi-meter not required for potentiometer calibration
- Control signal not required for calibration
- Options install into positioner via plug and socket
- Selectable fail position for loss of input signal; fail open, fail close, or fail as is
- Voltages: 230 VAC, and low AC or DC
- Heater and thermostat
- Mechanical Brake
- 4-20mA output transmitter with 3-SPST Relay Contacts
- Selectable input signal; 4-20mA, 1-5vdc, 0-5 VDC, 0-10 VDC, or digital
- Loss of command & feedback potentiometer fault detection
- Motor stall detection will sense when the motor has reached a stall condition & remove power from the motor.
- Voltages: 230 VAC, and low AC or DC
- Heater and thermostat
- Mechanical Brake
- 4-20mA output transmitter with 3-SPST Relay Contacts
- Datasheet – Peaktronic Positioner for Electric Actuated Gate Valve
- Drawing – Wiring Diagram 24 VAC – Peaktronic Positioner for Electric Actuated Gate Valve
- Drawing – Wiring Diagram – 120 and 220 VAC – Peaktronic Positioner for Electric Actuated Gate Valve
- OM Manual DHC Positioner Gen II
- OM Series 92 GEN II Modulating User Manual
- New Product Announcement – Peaktronic Positioner for Electric Actuated Gate Valve